FAQs

The CTI and it’s parent company have been producing Resurfacing Products since 1968. Acrylic Resurfacing has been in use since the early 1970’s. Polymer was added to the process in the early 1980’s to provide a superior bonding process of higher strength.

We acid etch and power wash the existing concrete to clean off dirt, remove loose aggregate and open pores. Next, a hand trowelled skim coat of polymer and Portland cement is applied to the surface as thinly as possible. This allows the maximum absorption of the polymer into the existing concrete rather than building up the existing surface. When the polymer dries, it becomes a part of the existing concrete. Because polymer is absorbed and dries as a part of the old surface, the polymer strengthens and makes dense the existing concrete, as the new application and old surface become an integrated piece.

The thinner we can apply the mixture the better. Usually between 3/32” to 1/8”. We are more interested in getting the polymer to penetrate the existing concrete than building the existing higher. The skim coat can be applied up to 2” thick to fill in low areas, level areas and fill holes. Areas that require more that 2” filling will be filled with a Portland cement gravel mix over a coat of epoxy prior to the skim coat being applied.

Once the skim coat is trowelled on and the Colored Decorative Coat is sprayed, the surface is sealed with an a protective sealer. These sealers is non porous and UV protective.

The CTI Concrete System should not show wear providing that the Sealer is replaced as wearing occurs. We estimate this to take place no sooner than 3.3 years under normal traffic conditions for a solvent based sealer. Other type sealers will give you different result, ask your dealer which sealer is best for your application. As long as the sealer is in good condition any wear will be absorbed by the protective coating.

If you replace your existing concrete you will be paying the cost of rip-out, removal, forming and pouring. This takes larger equipment than the CTI Concrete System, which sometimes causes damage to the landscaping. When completed you will have new concrete that will stain, will absorb oil and will be subjected to the dangers of salts, and has a strength of 3,000 to 4,000 PSI.
Repairing concrete with the CTI Concrete System will be stronger than most concrete at 7,000 PSI, resist Stains, resist Oil Spills and prevent Salt Damage. Additionally, it will add value to your home or property by making an attractive presentation of your concrete surfaces.

YES. CTI is as useful indoors as well as outdoors. The CTI system can be applied in basements as well as kitchen and bath.

There are a variety of sealers to chose from when completing a project. To determine which sealer to use, your dealer will take into consideration what traffic it will receive, if it is inside or out, and how accessible it will be if a reseal is needed. CTI has 3 sealers that are approved for indoor use.

Concrete Technology Inc. offers a full line of concrete beautification and restoration products for both residential and commercial use. CTi has different products that can be used over concrete floors, existing countertops, and even walls. In the commercial setting, Concrete Technology manufactures a line of tough, durable epoxy and urethane floor coatings that can protect concrete even in the harshest of environments.

CTI’s systems achieve a look, texture and color of any type stone or look you require. A base coat is applied that fixes any imperfections in the original concrete. A design is then laid over it and a hopper gun shoots on a textured layer over that. A final clear coat is put over the system that is nonporous and protects it as well as makes it very easy to maintain. Mold, mildew, motor oil, etc. can be sprayed off with a regular garden hose. Common detergents can be used to remove tough or repetitive latencies.

We have a variety of standard colors to choose from. However, we can custom produce any color you wish for a minimal extra charge.

An average job will take 1 to 2 days. Larger, more complex jobs may take longer. Clean foot traffic is usually allowed within the same day.

CTI offers a 10-year limited material warranty on its Hallmark System against, dramatic fading, delamination, and general product failure.